Descripción
Specs Overview
|
SpeedyBee F405 Mini BLS 35A 20x20 Stack |
|
SpeedyBee F405 Min |
|
SpeedyBee BLS 35A Mini V2 4-in-1 ESC |
|
Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available. |
|
NOT Supported |
|
NOT Supported |
|
NOT Supported |
|
3-6S LiPo |
|
20 x 20mm 3.5mm hole size，Compatible with M2 and M3 screws/Silicone grommets |
|
32mm(L) x 35mm(W) x 14.2mm(H) |
|
13.5g |
Specifications
|
SpeedyBee F405 V3 30x30 Flight Controller |
|
STM32F405 |
|
ICM42688P |
|
Type-C |
|
Built-in |
|
AT7456E chip |
|
Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available. |
|
NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmware update |
|
NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis. |
|
Not supported |
|
Direct soldering |
|
Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input. |
|
8MB Onboard Flash |
|
Yes(CC pad on the front side) |
|
Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500. |
|
3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller. |
|
4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A. |
|
1 group of 9V output, one +9V pad on front side. The total current load is 3A. |
|
Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load. |
|
Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. |
|
M1 - M4 wires or soldering pads on bottom side. |
|
6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6 |
|
UART R5(UART5) |
|
Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc |
|
Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware. |
|
BZ+ and BZ- pad used for 5V Buzzer |
|
Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. |
|
Not Supported |
|
Not Supported |
|
BetaFlight(Default), INAV |
|
SPEEDYBEEF405MINI |
|
20 x 20mm 3.5mm hole diameter ，Compatible with M2 and M3 screws/Silicone grommets. |
|
30(L) x 32(W) x 7.8(H)mm |
|
9.6g |
| ProductName | SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC |
|
BLHeli_S J-H-40 |
|
35A * 4 |
|
45A(5seconds) |
|
DSHOT300/600 |
|
3-6S LiPo |
|
VBAT(Battery voltage, used to power the flight controller) |
|
Support (Scale=250 Offset=-500) |
|
20 x 20mm ∅3.5mm hole size，compatible with M2 and M3 screws/Silicone grommets. |
|
35 * 35 * 5.5mm |
|
7.2g |
