SpeedyBee F405 WING MINI Fixed Wing Flight Controller

Specifications

• MCU STM32F405, 168MHz, 1MB Flash
• IMU(Gyro&Accelerometer) ICM-42688-P
• Barometer SPL006-001
• OSD Chip AT7456E
• Blackbox MicroSD Card Slot
• UART 6 sets (USART1, USART2, USART3, UART4, UART5,
• UART6 - Dedicated for Wireless board Telemetry connection)
• I2C 1x Used for magnetometer, digital airspeed sensor
• ADC 4x (VBAT, Current, Analog RSSI, Analog AirSpeed)
• PWM 12x (9x pin headers + 2x solder pads + 1x "LED" pad)
• ELRS/CRSF Receiver Supported, connected to UART1
• SBUS Built-in inverter for SBUS input (UART2-RX)
• LED 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)
• Analog RSSI Supported, Named as "RS"
• Dual Analog Camera Switching Default to Camera1 Video Input (C1). Switch between C1 and C2 using ArduPilot Relay or INAV Modes/USER.
• Both cameras should have the same video format, either PAL or NTSC.
• Supported FC Firmware INAV: SpeedyBeeF405WING (default)
• ArduPilot: SpeedyBeeF405WING
• Weight 5.6g

• Input voltage range 7~26V (2~6S LiPo)
• Battery Voltage Sensor Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
• Battery Current Sensor 80A continuous, 150A peak Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
• TVS Protective diode Yes
• FC BEC output Output 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed Sensor, Telemetry module
• VTX & Camera power supply The VTX power interface Vv offers two power supply options: direct battery voltage or integrated BEC 5V (sharing the 5V4A Servo BEC voltage)
• By default, it is set to battery voltage
• (Ensure the VTX and camera input voltage range is compatible)
• Switching to 5V power supply is possible via pad jumper (using Servo BEC output)
• (If using this method, ensure the current requirements for both servo and VTX are sufficient)
• Servo BEC output Output 5V +/- 0.1V DC Continuous current 4 Amps, 5A Peak Voltage adjustable, 5V Default, 6V via jumper Designed for Servos.
• Weight 5.5g

• Wireless Configuration (long press BOOT button for 6 seconds to switch modes)
• INAV:Please make sure the MSP switch on UART 6 is turned on and set to a baud rate of 115200 ArduPilot:Please make sure the Serial 6 is set to baud rate 115200 and protocol Mavlink2 BLE mode, connect to Speedybee APP
• Wi-Fi (AP)mode, able to connect to Speedybee APP, QGroundControl APP, MissionPlanner, etc. WiFi: Speedybee eFLY-WIFI Password: 88888888
• Wi-Fi (STA)mode, able to connect to QGroundControl APP, MissionPlanner, etc.
• Step 1: turn on Personal Hotspot;
• Step 2: Set hotspot, locate NAME/Device Name/Hotspot name/etc.
• Step 3: change the current name to eFLY and the password is, 88888888
• Wireless off mode
• USB Port Type Type-C
• Buzzer 5V Active Buzzer
• Weight 3.2g